You are previewing Dynamic Methods and Process Advancements in Mechanical, Manufacturing, and Materials Engineering.
O'Reilly logo
Dynamic Methods and Process Advancements in Mechanical, Manufacturing, and Materials Engineering

Book Description

Engineering and design are often a necessary steps for an industry to become effective. Industry modeling can help to bridge the communication gap among engineers and system designers. Dynamic Methods and Process Advancements in Mechanical, Manufacturing, and Materials Engineering examines the principles of physics and materials science for analysis, design, manufacturing and maintenance of mechanical equipments and systems. Targeting researchers, practitioners, and academicians, this volume promotes innovative findings in mechanical, manufacturing and materials engineering.

Table of Contents

  1. Cover
  2. Title Page
  3. Copyright Page
  4. Editorial Advisory Board and List of Reviewers
    1. Associate Editors
    2. List of Reviewers
  5. Preface
    1. SECTION 1. GENERAL ASPECTS OF MECHANICAL ENGINEERING
    2. SECTION 2. MANUFACTURING
    3. SECTION 3. MATERIALS SCIENCE AND ENGINEERING
  6. Acknowledgment
  7. Section 1: General Aspects of Mechanical Engineering
    1. Chapter 1: Development of an Optimization Framework for Parameter Identification and Shape Optimization Problems in Engineering
      1. ABSTRACT
      2. INTRODUCTION
      3. CONCLUSION
    2. Chapter 2: Large Amplitude Forced Vibration Analysis of Stiffened Plates under Harmonic Excitation
      1. ABSTRACT
      2. INTRODUCTION
      3. MATHEMATICAL FORMULATION
      4. RESULTS AND DISCUSSIONS
      5. DETAILED STUDY ON OPERATIONAL DEFLECTION SHAPE (ODS)
      6. EFFECT OF ASPECT RATIO ON FREQUENCY RESPONSE
      7. CONCLUSION
      8. APPENDIX
    3. Chapter 3: Design and Evaluation of Hydro-Pneumatic Friction Damper Suspension System
      1. ABSTRACT
      2. 1. INTRODUCTION
      3. 2. DRY FRICTION DAMPING
      4. 3. RESULTS AND DISCUSSIONS
      5. CONCLUSION
  8. Section 2: Manufacturing
    1. Chapter 4: An Investigation into the Environmental Impact of Product Recovery Methods to Support Sustainable Manufacturing within Small and Medium-Sized Enterprises (SMEs)
      1. ABSTRACT
      2. INTRODUCTION
      3. THE UK MANUFACTURING INDUSTRY
      4. SUSTAINABLE MANUFACTURING THROUGH WASTE MANAGEMENT IN SMEs
      5. REMANUFACTURING VS REPAIRING
      6. CALCULATING THE ENVIRONMENTAL IMPACT OF PRODUCT RECOVERY METHODS
      7. PROCESS MAP DEVELOPMENT
      8. BOUNDARIES AND PRIORITISATION
      9. DATA COLLECTION
      10. RESULTS
      11. CONCLUSION AND FUTURE RESEARCH
    2. Chapter 5: Recycling of Waste Epoxy-Polyester Powders for Foam Production
      1. ABSTRACT
      2. INTRODUCTION
      3. CONCLUSION
    3. Chapter 6: Feature Recognition and Datum Extraction for Setup Planning and Operation Sequencing for Prismatic Parts
      1. ABSTRACT
      2. 1. INTRODUCTION
      3. 2. PROPOSED FEATURE RECOGNITION APPROACH
      4. 3. FEATURE RECOGNITION AND DATUM EXTRACTION
      5. 5. RESULTS AND DISCUSSION
      6. 6. CONCLUSION
      7. APPENDIX A
      8. APPENDIX B
      9. APPENDIX C
    4. Chapter 7: Laser Sub-Micron Patterning of Rough Surfaces by Micro-Particle Lens Arrays
      1. ABSTRACT
      2. INTRODUCTION
      3. EQUIPMENT AND EXPERIMENTAL PROCEDURE
      4. RESULTS AND DISCUSSION
      5. CONCLUSION
    5. Chapter 8: A Finite Element Study of Buckling and Upsetting Mechanisms in Laser Forming of Plates and Tubes
      1. ABSTRACT
      2. INTRODUCTION
      3. EXPERIMENTAL SET-UP FOR PLATE BENDING
      4. NUMERICAL MODELING
      5. RESULTS AND DISCUSSION
      6. CONCLUSION
    6. Chapter 9: The Impact of FEM Modeling Parameters on the Computed Thermo-Mechanical Behavior of SLA Copper Shelled Electrodes
      1. ABSTRACT
      2. INTRODUCTION
      3. THERMOMECHANICAL SIMULATIONS
      4. RESULTS AND DISCUSSION
      5. CONCLUSION AND FURTHER RESEARCH
    7. Chapter 10: Micro Machining of Nonconductive Al2O3 Ceramic on Developed TW-ECSM Setup
      1. ABSTRACT
      2. INTRODUCTION
      3. DESIGN AND DEVELOPMENT OF TRAVELING-WIRE ECSM SETUP
      4. PLANNING FOR EXPERIMENTATION
      5. RESULTS AND DISCUSSIONS
      6. SEM GRAPHS
      7. CONCLUSION
    8. Chapter 11: 3D Finite Element Modeling of High Speed Machining
      1. ABSTRACT
      2. INTRODUCTION
      3. CONCLUSION
    9. Chapter 12: A Finite Element Study of Chip Formation Process in Orthogonal Machining
      1. ABSTRACT
      2. INTRODUCTION
      3. FINITE ELEMENT METHOD
      4. RESULTS AND DISCUSSION
      5. CONCLUSION
    10. Chapter 13: Cold End Forming of Welded Steel Tubes
      1. ABSTRACT
      2. INTRODUCTION
      3. EXPERIMENTAL BACKGROUND
      4. FINITE ELEMENT MODELLING
      5. RESULTS AND DISCUSSION
      6. CONCLUSION
    11. Chapter 14: Study on Oxidation of Stainless Steels During Hot Rolling
      1. ABSTRACT
      2. INTRODUCTION
      3. EXPERIMENTAL
      4. RESULTS AND DISCUSSION
      5. CONCLUSION
  9. Section 3: Material Science and Engineering
    1. Chapter 15: Material Selection Using a Novel Multiple Attribute Decision Making Method
      1. ABSTRACT
      2. INTRODUCTION
      3. NOVEL DECISION MAKING METHODOLOGY
      4. EXAMPLES
      5. CONCLUSION
      6. APPENDIX
    2. Chapter 16: Attribute Based Selection of Thermoplastic Resin for Vacuum Infusion Process
      1. ABSTRACT
      2. 1. INTRODUCTION
      3. 2. LITERATURE OVERVIEW
      4. 3. IDENTIFICATION OF RESIN SYSTEM ATTRIBUTES
      5. 4. DECISION MAKING METHODOLOGY
      6. 5. SELECTION OF THERMOPLASTIC RESIN FOR VACUUM INFUSED WIND TURBINE BLADE – AN ILLUSTRATIVE EXAMPLE
      7. 6. CONCLUSION
    3. Chapter 17: Reciprocating Wear Behaviour of Two Dimensionally Reinforced Carbon-Phenolic and Carbon-Epoxy Composites
      1. ABSTRACT
      2. 1. INTRODUCTION
      3. 2. EXPERIMENTAL PROCEDURE
      4. 3. RESULTS AND DISCUSSION
      5. 4. CONCLUSION
    4. Chapter 18: Roughness Optimization of Electroless Ni-B Coatings Using Taguchi Method
      1. ABSTRACT
      2. INTRODUCTION
      3. TAGUCHI METHODOLOGY
      4. EXPERIMENTAL DETAILS
      5. RESULTS AND DISCUSSION
      6. CONCLUSION
    5. Chapter 19: Al2O3 Nanobricks via an Organic Free Route Using Water as Solvent
      1. ABSTRACT
      2. INTRODUCTION
      3. EXPERIMENTAL
      4. COMPOSITION OF SAMPLE
      5. CONCLUSION
    6. Chapter 20: Preparation of Copper Oxide (CuO) Nanoparticles and their Bactericidal Activity
      1. ABSTRACT
      2. 1. INTRODUCTION
      3. 2. EXPERIMENTAL
      4. 3. RESULTS AND DISCUSSION
      5. 4. CONCLUSION
  10. Compilation of References
  11. About the Contributors
  12. Index